ITI GURUJI

WELDER (NSQF LEVEL 4) MOCK TEST-05

Facebook
WhatsApp
Telegram
0%
529
Created on By ITI GURUJI

WELDER

WELDER MOCK TEST -05

WELDER  च्या थिअरी  विषयाची  mock टेस्ट  तयार केली आहे. यामध्ये सर्व प्रश्न हे मराठी व इंग्रजी दोन्ही भाषेत सोबत दिले आहेत, त्यामुळे इंग्रजी प्रश्न व त्याचे तंतोतंत  मराठी भाषांतर  दोन्ही समजण्यास सोपे जाईल. तेंव्हा सर्व मॉक टेस्ट सोडवा, आपल्या मित्राना देखील  शेयर करा.

1 / 25

Category: WELDER

Which heat treatment process is very similar to annealing but the job are allowed to cool in air? कोणती उष्णता उपचार प्रक्रिया अॅनिलिंग सारखीच असते परंतु जॉब हवेत थंड होऊ दिले जाते?

2 / 25

Category: WELDER

What is the NDT method, used to detect surface and subsurface defects on ferrous metals, using iron power? लोह शक्ती वापरून फेरस धातूंवरील पृष्ठभाग आणि पृष्ठभागावरील दोष शोधण्यासाठी वापरली जाणारी NDT पद्धत काय आहे?

3 / 25

Category: WELDER

Which welding process is done by chemical reaction between a metal oxide and metal? मेटल ऑक्साईड आणि धातू यांच्यातील रासायनिक अभिक्रियाद्वारे कोणती वेल्डिंग प्रक्रिया केली जाते?

4 / 25

Category: WELDER

Which is the remedy for the contraction of weld metal due to excess of heat input that moves the base metal changes the angle? वेल्ड मेटलच्या आकुंचनासाठी कोणता उपाय आहे जो जास्त उष्णता इनपुटमुळे हलवतो ज्यामुळे बेस मेटल कोन बदलतो?

5 / 25

Category: WELDER

Which heat treatment process is employed to remove brittleness in a chisel? छिन्नीतील ठिसूळपणा दूर करण्यासाठी कोणती हिट ट्रिटमेंट प्रोसेस वापरली जाते?

6 / 25

Category: WELDER

What type of test is used for vessels, tanks and pipe containing pressure? वाहिन्या, टाक्या आणि दाब असलेल्या पाईपसाठी कोणत्या प्रकारची टेस्ट वापरली जाते?

7 / 25

Category: WELDER

What is the trouble shooting to wire wrapping on drive rolls of wire feeder in GMAW? GMAW मधील वायर फीडरच्या ड्राईव्ह रोलवर वायर रॅपिंग करण्यात काय त्रास होतो?

8 / 25

Category: WELDER

What should be the initial angle of two plates in a T joint if the final angle between them is 90° after completion of welding? वेल्डिंग पूर्ण झाल्यानंतर दोन प्लेट्समधील शेवटचा कोन 90° असल्यास टी जॉइंटमधील प्रारंभिक कोन किती असावा?

9 / 25

Category: WELDER

What is the reason that obstructed joints cannot be welded by electron beam welding process? इलेक्ट्रॉन बीम वेल्डिंग प्रक्रियेद्वारे अवरोधित जॉइन्ट वेल्डिंग करता येत नाहीत याचे कारण काय आहे?

10 / 25

Category: WELDER

What is the weld defect if wire feed speed too high? वायर फीड गती खूप जास्त असल्यास वेल्ड दोष काय आहे?

11 / 25

Category: WELDER

Which heat treatment process, if material is softened & suitable for machining? मटेरियल मऊ आणि मशीनिंगसाठी योग्य असल्यास कोणती हिट ट्रिटमेंट प्रोसेस करावी ?

12 / 25

Category: WELDER

What is percentage of deposition efficiency in FCAW process? FCAW प्रक्रियेत जमा कार्यक्षमतेची टक्केवारी किती आहे?

13 / 25

Category: WELDER

Which metal is welded with self shielded type FCAW? कोणत्या धातूला सेल्फ शील्डेड प्रकार FCAW सह वेल्डेड केले जाते?

14 / 25

Category: WELDER

What is the effect in MIG / MAG welding for a short stick out distance? लहान स्टिक आऊट अंतरासाठी MIG/MAG वेल्डिंगमध्ये काय परिणाम होतो?

15 / 25

Category: WELDER

What is basic safety environmental condition for the welding area? वेल्डिंग क्षेत्रासाठी मूलभूत सुरक्षा पर्यावरणीय पोजिशन काय आहे?

16 / 25

Category: WELDER

What is the operation to clean the cylinder valve before fixing the regulator to the argon cylinder? आर्गॉन सिलेंडरला रेग्युलेटर फिक्स करण्यापूर्वी सिलेंडर व्हॉल्व्ह साफ करण्यासाठी कोणते ऑपरेशन केले जाते ?

17 / 25

Category: WELDER

What Non-destructive test is done using coloured dye and fluorescent liquid to find minute cracks? मिनिट क्रॅक शोधण्यासाठी रंगीत डाई आणि फ्लोरोसेंट द्रव वापरून कोणती नॉन-डिस्ट्रक्टिव्ह टेस्ट केली जाते?

18 / 25

Category: WELDER

Which gas/mixture is likely to reduce the spatter loss in FCAW? कोणता वायू/मिश्रण FCAW मध्‍ये स्‍पॅटर लॉस कमी करण्‍याची शक्यता आहे?

19 / 25

Category: WELDER

How much time it takes for the thermit mould to cool, after welding by thermit process? थर्मिट प्रक्रियेद्वारे वेल्डिंग केल्यानंतर थर्मिट मोल्ड थंड होण्यासाठी किती वेळ लागतो?

20 / 25

Category: WELDER

What defect will occur in the weld metal if the arc voltage and travel speed is low in MIG / MAG welding? MIG/MAG वेल्डिंगमध्ये आर्क व्होल्टेज आणि ट्रॅव्हल स्पीड कमी असल्यास वेल्ड मेटलमध्ये कोणता दोष निर्माण होईल?

21 / 25

Category: WELDER

How much gas flow rate is required to weld a butt joint with 0.8 mm dia MS filler rod of wire feed rate 3 - 4 m/min at 18 to 20 volts? 18 ते 20 व्होल्ट्सच्या वायर फीड रेट 3 - 4 मीटर/मिनिटच्या 0.8 मिमी व्यासाच्या एमएस फिलर रॉडसह बट जॉइंट वेल्ड करण्यासाठी किती गॅस प्रवाह दर आवश्यक आहे?

22 / 25

Category: WELDER

23 / 25

Category: WELDER

What is the name of heat treatment process where the steel is reheated to a suitable temperature below the critical point (heating) to improve the toughness and ductility? स्टीलमधील टफनेस आणि लवचिकता(डक्टिलीटी) सुधारण्यासाठी क्रिटीकल पोइन्ट (हीटिंग) खाली योग्य तापमानात पुन्हा गरम केले जाते, या हिट ट्रिटमेंट प्रोसेस ला काय म्हणतात जेथे ?

24 / 25

Category: WELDER

What is the main purpose of ‘Normalising’ steel? स्टीलचे 'नॉर्मलायजिंग(नॉर्मलायझींग)' करण्याचा मुख्य उद्देश काय आहे?

25 / 25

Category: WELDER

Which combination of metal and shielding gas give excellent cleaning action in GMAW welding process? GMAW वेल्डिंग प्रक्रियेत मेटल आणि शील्डिंग गॅसचे कोणते मिश्रण उत्कृष्ट साफसफाईची क्रिया देते?

Your score is

0%

Exit

जर आपल्याला हि ऑनलाईन टेस्ट आवडली असेल तर अवश्य 5  स्टार  रेटिंग द्या, तसेच काही सुधारणा असल्यास आवश्य कॉमेंट करा.

धन्यवाद

Also Read...

Leave a Comment

Categories
Site Statistics
  • Today's page views: : 77
  • Total visitors : 503,459
error: Content is protected !!